How to Properly Test Your Pool Water With A Pool Testing Kit

As the warm weather approaches, your pool will undoubtedly be used more often. Because of this, you must know how to make sure that the pool is safe for use. You’ll have to check the water quality, and you’ll do so with pool test kits!

If you are unsure of how to use a pool test kit, we have prepared a guide to help you.

Frequency of Tests
You will need to determine the right time to test your pool water. Although there isn’t a specific guideline, the more often you check, the better!

Testing for chlorine and pH levels should be done at least twice a week, while testing for alkalinity should be done once a week. For acid tests, perform them whenever you’re adjusting the pool’s pH levels. As for other tests like calcium hardness, total dissolved solids, and cyanuric acid levels, they should all be done once a month.

That said, let’s get into the know-how of using pool testing kits:

Step 1: Grab a sample
Use a plastic tester to collect a sample of the pool water. Because the chemical composition of the water near the surface and at the bottom of the pool is different, you’ll have to take a sample from both depths. For a sample from the bottom, dip the plastic tester at least 18 inches into the pool for more accurate results.

Step 2: Test for chlorine
To get accurate readings, make sure your vials are filled appropriately following the manufacturer’s guidelines. Then, add the appropriate solution to test for chlorine. With the right chemical to pool water ratio achieved, you can then cap the vial and start mixing. After a few seconds, the colors should change. Compare these colors to a guideline that is usually printed onto the plastic tester itself. This initial reading indicates free chlorine levels. By waiting a few minutes and comparing the colors once more, you’ll get a reading for residual chlorine.

Step 3: Test for PH levels
After thoroughly cleaning the plastic tester, repeat the first step. Then, look for the chemical sodium thiosulfate (No. 4) and add it into the sample to neutralize the chlorine. Then, add five drops of the phenol red indicator solution (No. 2). After mixing, compare it with the pH color standards. Do note that if your residual chlorine is higher than three, you’ll have to get it down to proper levels before proceeding.

Step 4: Test for acid demand
Make sure that you perform this test only after your chlorine residue and pH levels are at their proper levels. Do not throw away the water after the pH test, but instead add titrant. You’ll have to count each drop until the color reaches the 7.4 indicators. From this, you’ll find out just how much acid you’ll need to add to your pool to balance the pH levels.

Step 5: Test for alkalinity
Once again, only proceed with this test if your chlorine level has dropped down to normal. Clean the tester thoroughly and fill it up only until the lower dashed line. Add a drop of chlorine neutralizer, as previously mentioned in step three and mix. After that, add a reduction of the alkalinity indicator (No. 5B) and mix gently. Then, count each drop of solution No. Three you add into the tester until the color changes to either light green, light yellow, or goes transparent. Multiply the number of drops by ten, and that’s your pool’s alkalinity.

We hope that our guide has given you the much-needed knowledge to use pool tester kits properly.

If you a looking for a top-rated pool maintenance company to help you test your pool water, call Purple Heart Pools now! We are happy to help.

5 Reasons to Start a Weekly Pool Pump Maintenance

Having a pool is a luxury, not only because it affords you to bring people in and socialize, but it also allows you to have space to be healthy, fit, and beautiful. Having one brings so many wonders to the mental, physical, and emotional well-being of every person who gets to enjoy it. Swiming can reduce stress and prevent depression. It also gives the children plenty of opportunities to have fun too.

This is why it is essential to take good care of the pool. You have to make sure that the pool pump is at its optimum efficiency. The cost of repairs for pool pump malfunctions is high, not to mention that it will also affect the health of those who swim inside the pool.

Preventing that from happening will save you a fortune. Follow the guidelines to ensure that your pool continues to help you make beautiful memories with the family. Here are the reasons that you should keep the pool pump working.

1. The pump is an essential part of the pool.

The pool pump is the pool’s circulation system. It is the pool’s central control that sends water through the filter, removing debris, dirt, and dust. If it malfunctions, improper filtration ensues. That’s when algae start to form. It will fill your pool and turn it into a bright, mossy green. Who wants to swim in that?
Moreover, the filthy water can cause more problems to the entire pool. The pool’s electrical and mechanical components are going to erode. If left unresolved, it will degrade the pool walls and flooring.

2. Filth accumulation causes damage.

A pool that’s been accumulating dirt will have increased wear and tear on its pool pump. That means that the problem is right around the corner. If you notice your pumps making odd sounds, have decreased water levels, or are causing the circuit breaker to trip more often, they are broken. These problems come from a lack of maintenance, which leads to filth accumulation in and around the pool pump.

3. It keeps the water clean.

If you’re asking about the lifespan of the pool pump, the answer will depend on several factors. These include the size of the pool, the type of piping it has, and the number of people swimming in it, as well as the frequency of their swimming. Only a pool professional can tell you the answer. They have the training, the skills, the knowledge, as well as the equipment to determine the right amount of time that the pool pump should be running.

4. It is energy-efficient.

The pool size is the most significant factor to consider if you want to know exactly how long you need your pool pump to run. The larger your pool, the longer the pool pump needs to pump. Bigger pumps consume more energy, which results in higher utility bills. However, when the pool pump ceases to work, it no longer matters if it’s a big pump or a small one.

Filth will always make your pump function inefficiently. If your pump is dirty, it needs to work twice as hard, which requires it to consume more energy. More energy consumption means higher utility bills, so a properly running pool pump is energy-efficient.

5. Repairs are costly.

Pool owners spend about $600 on average per pool fixes. The cheapest repair can be $80, while the most expensive ones cost around $2,500. With this, it will be enough to convince you to keep your pool adequately maintained. Weekly cleaning will save you from paying much higher expenses.

A broken pool pump will prevent you and your family from enjoying the benefits that a swimming pool brings. Moreover, the repairs will be costly. If you don’t want to encounter these disadvantages, it is best to invest in your pool pump’s weekly maintenance. Hire the best pool professionals, and they will take good care of your pool.

If you a looking for a top-rated pool maintenance company in Jacksonville, get in touch with Purple Heart Pools now! We are happy to help.

A Guide to Cleaning Your Swimming Pool Waterline Tiles

Waterline tiles are the ones installed by the edge of your pool where the water meets the line. Cleaning this is one of your responsibilities as a swimming pool owner. Over time, calcium deposits and natural stains accumulate on the edges, leaving a weird ring around the waterline.

Regular cleaning and proper maintenance are crucial if you want to keep it looking appealing all year long. Read on for our guide on how to make your swimming pool’s waterline tiles as shiny as the first time you installed them:

But first, what is that stuff?
That unsightly line that forms around your pool’s waterline is the result of scaling and staining. As water evaporates, calcium deposits are pushed to the sides of the pool, leaving a whitish-grey colored scum that is difficult to remove. There are two types of scaling we usually see in swimming pools: calcium carbonate and calcium silicate. Let’s take a closer look at each one.

1. Calcium carbonate
Calcium carbonate appears as a flaky white crust on the pool’s surface. It bubbles up if you pour muriatic acid on the area. Fortunately, calcium carbonate is easy to scrub off using a pumice stone or a stain eraser.

2. Calcium silicate
Calcium silicate is trickier to remove because it takes a longer time to settle into your pool’s waterline. Calcium silicate appears as a whitish-grey scum and does not react to muriatic acid. This type of scaling takes more effort and a lot of elbow grease to strip off.

Tips for tackling staining and scaling
As with all things, prevention is better than cure. Don’t wait for the scum to build up. Keeping your pool’s waterline stain-free means you have to clean it regularly. Algae from decaying leaves and other debris create a chemical imbalance to your swimming pool, causing stains when they cling on to the tiles. Make sure to vacuum your pool’s surface at least once a week to remove dirt.

If you see signs of that scum line appearing on your pool’s waterline, it’s time to bring out the big guns. Extensive cleaning can be time-consuming, so it’s wise to start in small areas per day. You can try using all-natural, homemade cleaning solutions for minimal grimes. Vinegar, baking soda, toothpaste, and borax are some of the everyday household items that make effective cleaners. Make a paste and scrub the ring with a used toothbrush.

For tougher stains, there are commercial tile cleaners you can get at your local hardware store. These are acid-based products that are very strong, so you need to use them with caution. Always wear protective gloves and mask to avoid inhaling harsh chemicals.

Big jobs may require you to call for reinforcements. Hiring professional pool cleaning services ensures that the job gets done quickly and adequately. They have special equipment and cleaners that can strip away the toughest stains in your pool’s waterline tiles. Bringing the professionals in at least once a year will keep your pool looking fresh and save you the costly expense of having to re-tile your pool’s waterline.

If you a looking for a pool cleaning service in Jacksonville, get in touch with Purple Heart Pools now! We are happy to help.

Spot Pool or Hot Tub Leaks in 3 Steps

Compared to most problems that show that something is wrong with your pool or a hot tub, a leak is probably one of the most difficult problem to spot because of how a pool is built.

Think about it: how could you possibly spot a leak in a pool or hot tub when it’s full of water in the first place

It may seem impossible at first but when you have the right knowledge, the task will not be so daunting.

There are various ways to detect leakage in a pool or a hot tub and understanding how to find the cause will help you save time and money.

STEP #1: Watch out for these signs
– Water-quality issues or a sudden presence of algae
– Loose tiles or cracks in the pool deck or the surrounding area
– Loose coping stones
– Check for tree roots that can lift the pool deck, plumbing, or pool walls
– Look for cracks or gaps in the bond beam
– Extra soggy soil or grass near the pool, spa, pumps or pool plumbing equipment could me serious issues
– Water levels consistently dropping overnight

STEP #2: Go deeper into the inspection with a test
Once you spotted the signs of possible leakage, then it’s time to carry out a test to confirm the actual leak. The best DIY way to implement the process of leakage confirmation is the evaporation test.

You will need a bucket and an indelible pen to do the evaporation test. Start the test by filling a bucket with pool water and placing it on the deck right beside the pool or hot tub. Mark the water level of both the pool and bucket with an indelible pen. Afterward, turn off the circulation and wait for two to three days.

Once a few days have passed, take a look at the water in the bucket and the pool and then measure the distance between the line marked on the first day and the waterline now. If a pool is fine, then both the water in the bucket and pool should evaporate equally. However, if the pool’s first-day line and current waterline distance are significantly more than that of the bucket’s, then it’s safe to assume that your pool has a leak.

STEP #3: Call the professionals once you spot a leak
Once you’ve confirmed that your pool or hot tub has a leak, then it’s time to call a pool repair professional. A pool repair professional will bring a geophone or pressure testing equipment as part of the repair.

A leakage in a swimming pool or hot tub may seem like a simple problem at first, but it is absolutely important to remember that it should not be overlooked. By following the steps mentioned above, you can save your time, money, and most importantly, your pool or hot tub.

If you don’t have much time to maintain your pool yourself, leave it to the professionals. Call Purple Heart Pools today. We offer various pool care services, so you can enjoy your free time swimming rather than constantly maintaining your pool.

Closing Your Pool Down For The Winter

There are months that you will not be using your swimming pool, spa, or hot tub, such as during the winter. There is a right way to do winterizing or pool closing, and this is important because closing too soon or too late can lead to problems. When you do it too early, there’s a possibility of algae overgrowth. If you do it too late, you may already have a lot of mess to deal with.

Plumbing, equipment, and pool structure will freeze in winter, so it is crucial to close them ahead of time. One week before your planned heavy-duty winterizing work, start testing the water for pH level, alkalinity, etc. The chemical components of your pool should be balanced to keep it sanitary. Also, winterizing takes days to complete, so you must be prepared for the hard work.

Here are the tips on how to winterize your swimming pool, spa structure, or hot tub:

Prepare the Materials That You Will Need

Winterizing is an extensive job that you may want to leave to the professional cleaners. But if you are doing the cleaning yourself, it is best to have everything that you need before you start with the work.
You will need:

– Air compressor
– Vacuum or portable pump
– Pool test kit
– Brushes
– Sanitizer
– Stabilizer
– Algaecide
– Non-toxic antifreeze pool kit
– White grease

Inspect the Pool for Repair Needs

Inspect the pool, spa structure, and hot tubs carefully. If there are repairs needed, do them before the pool closing. Everything must work properly before you winterize the structure for the season.

Clean and Treat the Water

Clean the water of any debris, wastes, and dirt using your vacuum or portable pump. Then, treat the water to ensure that its pH levels, alkalinity, and calcium hardness are all balanced. This will prevent the water from being corrosive once the temperature drops to the freezing point and below. Add the winterizing chemicals, including sanitizer, stabilize, or algaecide before draining or covering the structure. Always read the instructions on the chemical container to ensure that you are adding the right amount.

Lower the Water Levels

Instead of draining, it is best to keep the pool full of water. You just have to lower the water levels depending on the pool and cover that you will use. For example, a vinyl-lined pool must have water that is one inch below the skimmer mouth. Meanwhile, a plaster finish with a solid material cover should be one to six inches below the mouth or tile line.

Clean the Piping, Valves, and Pumps

Drain the piping as thorough as possible using a tank vacuum or air compressor. Also, drain water from the heater and filter. Then, add a non-toxic antifreeze solution. Valves should also be dried thoroughly, and those that are below the water level should be sealed securely also removing the plugs and drain the pumps. Add an antifreeze solution and apply lubricant to prevent winter corrosion.

Cover The Pool

Once everything is cleaned and drained, cover the pool carefully to ensure that no debris will get through.

Closing the pool or winterizing is essential to protect the structure during the season that you can’t use it. Understanding how it is done properly will ensure that your pool is protected and safe. If this task does not sound like something you would want to dive in or if you don’t have much time for it, leave it to the professionals.

If you have little time to maintain your pool yourself, leave it to the professionals. Call Purple Heart Pools now. We offer various pool care services, so you can enjoy your free time swimming rather than maintaining your pool.

Pool Maintenence 101 – 6 Different Types of Pool Cleaners You Can Use

Owning a swimming pool is such a nice thing—you can take a swim anytime you want, level up your hosting of a party, and keep yourself cool during the summer. Those are all fun—until you have to clean it. While you can hire professionals to clean and maintain your pool, at some point, you still have to do the cleaning to make sure that your swimming pool does not become a dirty swamp and a breeding ground for mosquitoes. That said, you need the right cleaning materials.

Here are the different pool cleaners and what you should buy them for:

Manual pool cleaners

Manual pool cleaners are the basic, cheapest, and simplest tools you can have. These include handheld vacuums, skimmers, and scrub brushes. They are usually attached to a telescoping scope, so you can reach the deepest part of the pool. Manual pool cleaners allow you total control when cleaning the sides and the bottom, and sweeping algae and other particles. On the downside, manual cleaners are the physically hardest type to use, although some people find it therapeutic. They are also time-consuming, so you may need to set at least an hour when cleaning.

Handheld pool vacuums

Handheld pool vacuums work like you are vacuuming the floors inside your house. You maneuver it across the surface of the pool. They can help you improve your pool’s filtration system inexpensively.

Suction pool cleaners

Suction pool cleaners or suction-side cleaners are attached to the pool’s pump and use its suction power to scoop up debris. A long hose is attached to the skimmer, and it becomes a water-based vacuum cleaner that moves around the pool in a predetermined pattern while cleaning. Suction pool cleaners may use more electricity than other cleaners because they require the pump to be running during the cleaning process.

Robotic pool cleaners

With technologies advancing faster, automatic tools are everywhere, and you can enjoy a robotic pool cleaner now. This is an automatic pool vacuum that has a built-in filter and motor, and it can sweep even the smallest particles from the pool surfaces. Some robotic pool cleaners have remote control and four wheels, which are useful for spot cleaning. They are by far the easiest to use because they are autonomic once you turned in on, and they are also energy efficient.

Pressure pool cleaners

Pressure pool cleaners or pressure-side cleaners use the pool’s pump so they can move around the pool and clean surfaces. A pressure pool cleaner comes with a filter bag and is mounted on wheels. They are ideal for pools with large debris and dirt to remove.

In-floor cleaning system

If you are still in the planning stage of adding a swimming pool in your property, consider an in-floor cleaning system. This luxurious system is an automatic vacuum system installed during the construction of the pool. It includes jets and booster pumps, and when the system is turned on, high-pressured water swirls are created, leading the debris toward the main drain and into the filtration system.

There are various types of pool cleaners you can pick up to maintain your swimming pool depending on your budget and willingness to do physical work. But when the time doesn’t permit you to keep it clean, it is best to leave it to the professionals.

If you have little time to maintain your pool yourself, leave it to the professionals. Call Purple Heart Pools now. We offer various pool care services, so you can enjoy your free time swimming rather than maintaining your pool.

Basic Pool Supplies That a Pool Owner Needs to Have!

Your pool is more than just an oversized version of your bathtub. It requires equipment, tools, and supplies for its care and upkeep. Pool owners in Florida who have already been keeping their pools for a long time would probably have some of these essential materials. First-time owners need to look for these supplies as soon as possible. The following pool supplies are a must in every pool owner’s coterie of pool maintenance and cleaning equipment.

Pool supplies for removing debris

Leaves, twigs, wrappers, fabric, and hair are some debris that accumulates and float on the surface of swimming pools. Algae can also build up, especially if the water’s chemistry is no longer balanced. To remove all these debris, you will need a telescoping pole. A telescoping pole lets you scoop floating debris. Its length helps you reach various corners of your pool without having to walk around too much.

Telescoping poles for swimming pools may be made with carbon fiber, alloy, or fiberglass. Since the debris you would remove from the pool would be wet and heavy, you need a telescoping pole that would withstand the debris weight. The pole itself should be lightweight so you will not get fatigued easily when using it.

Another equally essential tool you will need is the skimmer. The skimmer is a net attached to the end of your telescoping pole that collects the debris from your pool. Similar to the telescoping pole, the skimmer you need to buy must be durable enough to carry the wet and heavy debris it collects. Thus, invest in a decent skimmer that would last years. Since you will use this tool often, buying one with a high-quality would prove to be a good value for your money.

Pool equipment for brushing and vacuuming

Algae, grime, suntan oils, and soap residues could stick and gather on the walls and floors of your swimming pool. Scrub off these surfaces regularly to keep your pool safe and hygienic for users. If your pool is small, you can use a typical hand brush to scrub your pool walls. However, if your pool is deep and wide and draining the water is not an option, you would need more sophisticated equipment for brushing, particularly, a pool vacuum cleaner.

After you’ve brushed the walls, you would need to extract the scum you removed. By buying a pool vacuum cleaner, you can scrub the deeper parts of your pool and suck out the residues at the same time. Choose a pool vacuum cleaner with a durable hose to avoid choking that can endanger its user. Investing in a decent pool vacuum cleaner would pay off dividends for you in the long run.

Some necessary pool supplies can be expensive.

As a pool owner, it might be impractical for you to buy everything that your pool needs to have. You might have no time or money to buy everything listed here. Some necessary supplies, such as chemicals to balance your pool, aren’t included here because you need a professional to mix and put them in your pool.

If that’s the case, it’s best to hire a pool cleaning and maintenance company in Jacksonville. They have all the supplies and tools needed to keep your pool clean and safe. All you have to do is to let them perform regular cleaning and maintenance for you. Zero hassle for you, and zero dollars would be spent on cumbersome equipment and advanced chemicals.

Purple Heart Pools is a top-rated pool maintenance company in Jacksonville, get in touch today to see how we can help.

Our Tips For Cleaning a Green Pool

There’s nothing more annoying than jumping into a pool, only to find that it’s a green pool. But what exactly is a green pool? It’s a pool that has been overtaken by algae. When you have a green pool, that means a wide variety of aquatic plants have started to invade every nook and cranny of your pool. This is why your pool is filled with green-tinted water.

Having a green pool is quite a disaster, but it can be cleaned. The goal is to ensure your pool’s water will become as clear as it used to be in just a few days. It will take some commitment and manual labor. Regular pool cleaning and maintenance are important. To help you out, here’s what you need to do to clean a green pool:

Preparation

Let’s start with preparation. Preparation is key when treating a green pool. The first thing you need to determine is the chemical situation of your pool. This involves checking the chlorine and pH levels of your pool. It’s best to have one to three ppm of free chlorine to stabilize the pH level of the pool water. Afterward, you need to run a filter for 24 hours to clear out the algae, aquatic plants, and other pool debris such as leaves and twigs. Finally, you need to use a pool brush to scrub the sides and bottom of your pool.

Pool Shocking

The next thing you need to do is pool shocking. That means you have to add the right amount of chlorine at once to get rid of flourishing algae. There’s a vast array of pool shocks or concentrated chlorine out in the market. They come in powder or liquid form. First off, turn on your pool pump to get the water circulating. Then, pour your pool shock into the pool. You’ll want to disperse the shock evenly throughout the pool with the help of the pump. This will ensure that it will kill any algae that are growing in your pool. Once they’re dead, keep the filter running for a few days to clean the dead algae out completely.

Pool Cleaning

Pool cleaning is important. Once you’re done with pool shocking, you have to make sure that you get the dead algae entirely out of the water. Dead algae will make your pool cloudy. As mentioned, keep the filter running 24/7 for a few days until the water becomes crystal clear again. Also, you have to brush the sides of the pool to ensure that any algae sticking to them will be eliminated too. Finally, vacuum the bottom of the pool to get rid of any dead algae that sank to the bottom. With regular brushing and vacuuming, and if you keep the filter running 24 hours a day, you can expect your pool to have clear water within the next five days.

Green Pool Prevention

As always, prevention is better than cure. This also applies to pool cleaning and maintenance. As you know, cleaning a pool is a tedious task, and the whole process can put your pool out of commission for a week. After dealing with a green pool, chances are you want to make sure it doesn’t happen again. That said, make sure you keep at least 1.0 ppm of free chlorine in the water at all times. Test and adjust the water chemistry regularly, at least two to three times a week.

Make sure you have a way of keeping the pool chlorinated, even when you’re away. In the end, nothing beats regular maintenance. That’s the best way to make sure your pool is well-cared for and has crystal clear water.

Purple Heart Pools is a top-rated pool maintenance company in Jacksonville, get in touch today to see how we can help.

How to Extend Your Pool’s Life.

It’s great to have a swimming pool at home. You can swim in it all you want, all year round, particularly during summer.

A swimming pool is a luxury, which means not every home has one. If yours does, you should take good care of it with regular maintenance and cleaning. Doing so will not only make the pool safe to swim in, but it will also go a long way towards preserving the pool’s life span. It’s also better to pay for regular maintenance and cleaning than expensive repairs and new pool equipment in case something breaks down.

As a homeowner, how should you go about maintaining and cleaning your swimming pool? If you want to extend your swimming pool’s life, here’s what you should do:

Swimming Pool Cleaning

The most important thing you need to do to maintain a healthy and long-lasting pool is clean it, of course. The schedule of cleaning actually depends on how often and when the pool is used.

That said, it’s best to have a regular maintenance schedule. If the pool is used frequently, then you may want to clean it on a weekly basis. Otherwise, you can opt for biweekly or monthly cleaning. But if you ever host a pool party, you should clean the pool after the festivities end.

When cleaning, make sure that you don’t stop at adjusting the chemicals in the water. You also need to maintain the sides, bottom, and the filtration system. Use a skimmer to remove debris, such as leaves, flowers, and pollen, from the pool.

Swimming Pool Equipment

When it comes to swimming pool maintenance, proper use and handling of equipment shouldn’t be neglected. You have to take that into consideration for both the summer and winter months.

This entails opening and closing your pool immediately to keep it safe and healthy. Not closing your pool correctly will cause problems over time. Also, pool equipment and chemicals should be properly stored in a secure place, particularly during the off-season.

Swimming Pool Repairs

You may need to have your swimming pool repaired from time to time. That’s why you should always be on the lookout for problems with your pool and its equipment. If left unattended or taken for granted, chances are what should’ve been minor repairs will become major problems. Fixing such problems can be quite costly.

For instance, if you notice a tear in your pool’s lining, contact a repairman to have it fixed as soon as possible. The same is true for your filters if they don’t seem to work the way they should.

Chemical Balance

Finally, there should be a continuous balance of chemicals in your swimming pool. It can be pretty daunting to get that right. You may have to try again and again; however, it is imperative that you don’t give up on it. It’s important that you keep the right balance of chlorine and pH level when it comes to your pool’s water.

Doing so will ensure the utmost cleanliness of your swimming pool, the safety of the water, and the privilege of being able to make the most out of your swimming pool.

Purple Heart Pools is a top-rated pool maintenance company in Jacksonville, get in touch today to see how we can help.

Cleaning and Maintaining Different Pool Filter Types

When you splash around in your swimming pool during the summer, you will leave behind a ton of debris that your filter will pick up from the water. Your pool filter plays a crucial role in keeping its water free of debris and impurities, soy you need to keep it clean and well maintained. When summer turns to fall, which will eventually give way to winter, your pool will lie dormant for some time. It is during this time (i.e., the cold months) when you should clean your pool filter.

Even if your pool is relatively new, you should still maintain your pool filter regularly. That will go a long way towards the upkeep of hygiene, chemical balance, and water circulation in your pool. Maintenance extends the lifespan of your pool filter, enabling it to perform well for a much longer period. As long as your pool filters are working, you can prevent more expensive health and pool issues from arising.

Commonly-used types of pool filters in Florida

Pool owners in Florida use different types of filters. Before you start cleaning and maintaining your filter, you need to know what kind of filter your pool has so that you’ll know how to do the cleaning and maintenance correctly. Below is a list of commonly-used swimming pool filters in Florida.

1. Cartridge Filter

Cartridge filters have two parts: the coarse cartridge frame and the finer mesh structure. The former traps larger pieces of debris, whereas the finer mesh structure collects smaller dirt and fluid impurities, such as suntan and shampoo. These two components work together to ensure that only clean water enters your pool. Cleaning a cartridge filter is pretty straightforward. You only have to remove the cartridge, place it near your house’s drainage, and use a pressure washer to hose the debris off.

2. Sand Filter

Unlike a cartridge filter, sand filters become more effective as they gather more debris. That’s because sand filters are designed to incorporate into the filtering mechanism itself the sediment they trap. The filtered water passes through while the sediment gets stuck and becomes part of the filtering element of the sand filter. The downside with sand filters is that the small sediment they trap can get stuck in the pool filter’s pore spaces, reducing water flow in between those gaps. Cleaning your sand filter this autumn will help keep the pore pressure at an acceptable level.

To clean this type of filter, you first have to shut down the pump that brings it water. Once the pump is closed, attach the filter’s backwash hose and set your pump lever settings to “backwash.” Once you turn on your pump again, it will expel the dirt it accumulated last summer. A separate pipe will drain the water containing the dirt. Then, turn the setting back to “rinse” before you shut the pump off for the winter.

3. Diatomaceous Earth (DE) filter

A diatomaceous earth (DE) filter also has a backwash setting, like a sand filter. But these types of filters are made of the remains of siliceous microscopic organisms called diatoms. Because of these diatoms’ size, they can trap finer sediment than what sand filters and cartridge filters can. The high filtering efficiency of DE filters makes it the most expensive option among all filters, which is why those who own a DE filter need to extend the lifespan of their filter to get the most bang for their buck. DE filters can also become clogged over time, which contributes to reduced water flow. Cleaning a DE filter is like cleaning a sand filter. All you need to do is to shut your pool’s pump, activate the backwash setting, and rinse.

Hire a professional to maintain your pool filter

Regular pool filter cleaning and maintenance is a must if you want to keep your filter working for years to come. If you have no more time to clean your pool filter before the cold season comes, you can let a professional do it instead.

Purple Heart Pools is a top-rated pool maintenance company in Jacksonville, get in touch today to see how we can help.