How to Properly Test Your Pool Water With A Pool Testing Kit

As the warm weather approaches, your pool will undoubtedly be used more often. Because of this, you must know how to make sure that the pool is safe for use. You’ll have to check the water quality, and you’ll do so with pool test kits!

If you are unsure of how to use a pool test kit, we have prepared a guide to help you.

Frequency of Tests
You will need to determine the right time to test your pool water. Although there isn’t a specific guideline, the more often you check, the better!

Testing for chlorine and pH levels should be done at least twice a week, while testing for alkalinity should be done once a week. For acid tests, perform them whenever you’re adjusting the pool’s pH levels. As for other tests like calcium hardness, total dissolved solids, and cyanuric acid levels, they should all be done once a month.

That said, let’s get into the know-how of using pool testing kits:

Step 1: Grab a sample
Use a plastic tester to collect a sample of the pool water. Because the chemical composition of the water near the surface and at the bottom of the pool is different, you’ll have to take a sample from both depths. For a sample from the bottom, dip the plastic tester at least 18 inches into the pool for more accurate results.

Step 2: Test for chlorine
To get accurate readings, make sure your vials are filled appropriately following the manufacturer’s guidelines. Then, add the appropriate solution to test for chlorine. With the right chemical to pool water ratio achieved, you can then cap the vial and start mixing. After a few seconds, the colors should change. Compare these colors to a guideline that is usually printed onto the plastic tester itself. This initial reading indicates free chlorine levels. By waiting a few minutes and comparing the colors once more, you’ll get a reading for residual chlorine.

Step 3: Test for PH levels
After thoroughly cleaning the plastic tester, repeat the first step. Then, look for the chemical sodium thiosulfate (No. 4) and add it into the sample to neutralize the chlorine. Then, add five drops of the phenol red indicator solution (No. 2). After mixing, compare it with the pH color standards. Do note that if your residual chlorine is higher than three, you’ll have to get it down to proper levels before proceeding.

Step 4: Test for acid demand
Make sure that you perform this test only after your chlorine residue and pH levels are at their proper levels. Do not throw away the water after the pH test, but instead add titrant. You’ll have to count each drop until the color reaches the 7.4 indicators. From this, you’ll find out just how much acid you’ll need to add to your pool to balance the pH levels.

Step 5: Test for alkalinity
Once again, only proceed with this test if your chlorine level has dropped down to normal. Clean the tester thoroughly and fill it up only until the lower dashed line. Add a drop of chlorine neutralizer, as previously mentioned in step three and mix. After that, add a reduction of the alkalinity indicator (No. 5B) and mix gently. Then, count each drop of solution No. Three you add into the tester until the color changes to either light green, light yellow, or goes transparent. Multiply the number of drops by ten, and that’s your pool’s alkalinity.

We hope that our guide has given you the much-needed knowledge to use pool tester kits properly.

If you a looking for a top-rated pool maintenance company to help you test your pool water, call Purple Heart Pools now! We are happy to help.

Spot Pool or Hot Tub Leaks in 3 Steps

Compared to most problems that show that something is wrong with your pool or a hot tub, a leak is probably one of the most difficult problem to spot because of how a pool is built.

Think about it: how could you possibly spot a leak in a pool or hot tub when it’s full of water in the first place

It may seem impossible at first but when you have the right knowledge, the task will not be so daunting.

There are various ways to detect leakage in a pool or a hot tub and understanding how to find the cause will help you save time and money.

STEP #1: Watch out for these signs
– Water-quality issues or a sudden presence of algae
– Loose tiles or cracks in the pool deck or the surrounding area
– Loose coping stones
– Check for tree roots that can lift the pool deck, plumbing, or pool walls
– Look for cracks or gaps in the bond beam
– Extra soggy soil or grass near the pool, spa, pumps or pool plumbing equipment could me serious issues
– Water levels consistently dropping overnight

STEP #2: Go deeper into the inspection with a test
Once you spotted the signs of possible leakage, then it’s time to carry out a test to confirm the actual leak. The best DIY way to implement the process of leakage confirmation is the evaporation test.

You will need a bucket and an indelible pen to do the evaporation test. Start the test by filling a bucket with pool water and placing it on the deck right beside the pool or hot tub. Mark the water level of both the pool and bucket with an indelible pen. Afterward, turn off the circulation and wait for two to three days.

Once a few days have passed, take a look at the water in the bucket and the pool and then measure the distance between the line marked on the first day and the waterline now. If a pool is fine, then both the water in the bucket and pool should evaporate equally. However, if the pool’s first-day line and current waterline distance are significantly more than that of the bucket’s, then it’s safe to assume that your pool has a leak.

STEP #3: Call the professionals once you spot a leak
Once you’ve confirmed that your pool or hot tub has a leak, then it’s time to call a pool repair professional. A pool repair professional will bring a geophone or pressure testing equipment as part of the repair.

A leakage in a swimming pool or hot tub may seem like a simple problem at first, but it is absolutely important to remember that it should not be overlooked. By following the steps mentioned above, you can save your time, money, and most importantly, your pool or hot tub.

If you don’t have much time to maintain your pool yourself, leave it to the professionals. Call Purple Heart Pools today. We offer various pool care services, so you can enjoy your free time swimming rather than constantly maintaining your pool.

Our Guide to Hot Tub Maintenance

Hot tubs are an excellent place for people to unwind and relax. These pools can be for private or communal use. Regardless of the kind of hot tub you own or operate, you need to keep it well-maintained and hygienic at all times. Here are some of the most vital maintenance tips for your hot tub:

Surface cleaning tips

Strong chemicals and rough scouring pads can cause damage to your hot tub’s surfaces over time. Instead, remove the build-up of grime on said surfaces using a nylon scrubber or soft rag. Use mild, non-abrasive, and non-foamy cleansers when you do this. For minor cleaning tasks, you can use regular baking soda as a cleanser. There are also products that you can buy to keep the glazed surfaces of your hot tub shiny.

To clean your hot tub’s vinyl door, prepare a mild soap solution of baking soda or one teaspoon dishwashing liquid mixed per eight liters of water. Use a sponge to apply the solution before rinsing it off with a stream of water from a hose. Open the vinyl door and wash the other side with water before wiping it down with a dry rag.

Proper pool use tips

Make sure to shower with fresh water before you soak in your hot tub. Doing this will ensure that no soap or detergent residue from your body or bathing suit will leave itself on your hot tub’s filters. This will extend the filters’ lifespan. Also, use the soapless rinse cycle instead of washing your bathing suit in soapy water.

When you fill your hot tub with water, use a pre-filter to ensure that the water that goes into your hot tub is clean. The pre-filter can be attached to your source hose or fixture to screen out metal ions, tannins, and organic contaminants that can ruin your water and hot tub.

When you’re done, drain the used water and refill your hot tub with a fresh supply of water. Make sure to follow the instructions in the pool manufacturer’s manual when draining and refilling. Draining and refilling will remove the detergent and soap particles that could have collected on the surface of your hot tub over time.

Spa filter cartridges tips

Your spa filter cartridges accumulate debris and mineral deposits over time. Thus, you need to unclog your filters regularly to keep your hot tub’s water flow running smoothly. Rotate your hot tub’s spray cartridges as you flush it with a jet of water to expel any particles that may have blocked the filter’s pleats. If your hot tub has been using a spa filter cartridge for three or more years, replace it with a new cartridge since the pleats may have been worn down.

Pool water chlorination tips

Chlorination helps make the water in your hot tub hostile to bacteria and renders other organic and chemical impurities in the water inert, ensuring your water’s cleanliness. Chlorinate your spa water according to the instructions of the chlorine solution manufacturer. Be careful not to use more chlorine solution then is recommended to prevent skin, eye, and lung irritation.

Energy efficiency tips

A hot tub’s energy efficiency refers to the amount of electricity it uses to keep the water warm. Make sure that the seal of the hot tub’s doors are tight to prevent heat from escaping. If there are signs of fading, cracking, and sagging in your hot tub’s door, replace it with a new one.

You should also ensure the energy efficiency of your hot tub’s heating system, especially during the winter. To protect the sensitive components of the pool’s heating system from freezing damage, wrap a vinyl-fiberglass winter blanket around your hot tub when it’s not in use.

Purple Heart Pools is a top rated pool maintenance company in Jacksonville, get in touch today!